Free Shipping
This Diver Down Snorkel Kit contains everything you need to properly snorkel your ride.
FITMENT:
- 2017 only Polaris Ranger 1000
- 2017 only Polaris Ranger 1000 Crew
- 2017 only Polaris Ranger 1000 Crew EPS
- 2017 only Polaris Ranger 1000 EPS
- 2017-2019 Polaris Ranger 900
- 2017-2019 Polaris Ranger 900 Crew
- 2017-2019 Polaris Ranger 900 Crew EPS
- 2017-2019 Polaris Ranger 900 EPS
-
This product will not work on any Ranger HVAC model
FEATURES:
- Custom powder coated riser bracket to keep risers straight, evenly spaced, and looking good
- Rubber grommets to hold riser tubes in place
- 1 ½”, 2” or 3” risers - based on specific model
- Heavy duty vinyl tubing to route difficult locations where the competition uses think tubing
- High heat silicon hose in those critical areas where the competition melts
- Bellows to keep water out of differentials and transmission
- All mounting hardware for complete installation
- Step-by-step instructions complete with detailed photos
BENEFITS:
- Provides clean, dry air to the engine and other parts needing venting
- Prevents mud, water, and debris from entering the engine and clutch housings when equipped
- Bellows allow the differential and transmission air to expand and contract without the need for long vent lines that can easily get plugged with mud or be pulled off
- Each kit is engineered and cut to fit your specific application
FAQ:
Why Snorkel?
Simply put – The right snorkel can be the best insurance you buy for your UTV. The right snorkel can protect you expensive investment from disaster when submerged deeper than OE rated water depth. On the other hand, the wrong snorkel can be your worst investment and nightmare. We’ve seen countless units come through our shop with leaking snorkels
How could that happen?
Snorkels leak for a variety of reasons. Installation errors account for a lot these. Many times, a do-it-yourselfer may get it right, but only for a short time. When pipes aren’t cut to correct length and things don’t line up quite right, many times the snorkel will prevent water, but only for a limited time, then the joint fails. One of the most common issues that we’ve seen is failure due to a heat source. When the snorkel runs close to heat source the snorkel material deteriorates during each ride. The material gets harder and more brittle and many times begins to deform. At some point the material cracks and begins to let mud and water in. Less expensive kits rarely provide the heat resistant material to account for this. Our goal is to avoid these areas. This can take more time and more material, but goes a long way to extending the life of the snorkel and the UTV.
What does a Snorkel do?
A Snorkel Kit is intended to provide clean, dry air to the engine and other parts needing venting on UTVs, such as clutches, differentials, transmission, carburetors, and fuel tanks. This doesn’t necessarily mean the UTV should exceed the OE manufacturer’s stated maximum rated water line depth. The Snorkel Kit is intended as additional margin of protection in the event that the UTV is inadvertently driven into water deeper than the OE manufacturer’s air intakes will tolerate. There are many considerations to make when increasing water line depth and a snorkel is just one component.
We know a little about taking off-road vehicles to the extreme - especially when it comes to deep water and mud. Trust us to protect your ride from deep water hazards with Diver Down Snorkels by High Lifter Products.
Note: You have to cut/trim plastic to install this kit.
There are no returns or refunds on any brand of snorkel.
RETURN POLICY
- Items must be returned within 30 days of receiving them
- Windshields with the protective covering removed are not returnable
- Special ordered & custom items are non-returnable
- All return expenses are the responsibility of the customer unless the incorrect part was shipped in error
- Exchanges will not be shipped until the return has been received
- A restock fee may be applicable depending on the situation/manufacturer
- RE-STOCK FEES below are the MINIMUM manufacturer charges deducted from your refund
- The Original shipping cost will be applied to any returned order that received free shipping when the order was placed
- All items must be returned in new/undamaged/uninstalled condition in original packaging
- All returns must be inspected by our team before a refund/exchange will be processed
- Returned items that do not meet these requirements may be denied a refund/exchange
Highlifter - 20%
-We ask for your year, make and model at the end of you order. We are not required to check fitment on the products that you selected. It is ultimately the customers responsibility to check fitment on all products they are ordering to make sure it will fit their vehicle. Fitment information (Year, Make and Model) are listed on each product page, if you are not sure you are always more than welcome to give us a call and speak to someone in our sales department.
You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (5 to 10 business days), and the time it takes your bank to process our refund request (24 to 48 hours).
If you need to return an item(s) please CLICK HERE FOR THE RETURN REQUEST FORM.
***Return Authorization emails are sent to customer within 2 business days. Remember to check ALL EMAIL FOLDERS after 48 hours as they do not always go into your inbox, if you still do not see it please give us a call***
