Free Shipping-
FITMENT:
-
Honda Pioneer 1000 (2016-2-23) - Honda Pioneer 1000-5 (2016-2023)
- Will not fit Pioneer 1000-6 model
- There are no returns or refunds on any brand of snorkel.
NOTE: For the Honda Pioneer 1000 Special or 1000 Limited Edition the compartment in the dash that the cup holder relocation bracket attaches to is not on these models. You will lose the use of this bracket and the factory cup holder.
FEATURES:
- First in the industry to utilize custom molded high temperature silicon hoses in routing areas
- Custom molded silicone hoses allow for easier installation, shorter install times with more reliable connections
- Works with factory cab enclosure and back glass application
- Utilizes the belt exhaust for heat dissipation by blowing belt exhaust across the manifold, same as factory
- Superior rear view as compared to other snorkels due to careful snorkel riser placement. It does not block the rear view when looking into the bed or behind the Ranger.
- Powder Coated Riser Bracket to keep risers straight, evenly spaced and looking good
- Rubber Grommets hold riser tubes in place and prevent rattles while riding
- 2” High Lifter riser caps
- Bellows allow the differential and transmission air to expand and contract without the need for long vent lines that can easily get plugged with mud or be pulled off
- All mounting hardware for complete installation
Benefits:
- Provides clean, dry air to the engine and other parts needing venting
- Prevents mud, water and debris from entering the engine and clutch housings when equipped
- Bellows allow the differential and transmission air to expand and contract without the need for long vent lines that can easily get plugged with mud or be pulled off
- Each Kit is engineered and cut to fit your specific application
FAQ
Why Snorkel? Simply put – The right snorkel can be the best insurance you buy for your UTV. The right snorkel can protect you expensive investment from disaster when submerged deeper than OE rated water depth. On the other hand, the wrong snorkel can be your worst investment and nightmare. We’ve seen countless units come through our shop with leaking snorkels
How could that happen? Snorkels leak for a variety of reasons. Installation errors account for a lot these. Many times a do-it-yourselfer may get it right, but only for a short time. When pipes aren’t cut to correct length and things don’t line up quite right, many times the snorkel will prevent water, but only for a limited time, then the joint fails. One of the most common that we’ve seen is failure due to a heat source. When the snorkel runs close to heat source the snorkel material deteriorates during each ride. The material gets harder and more brittle and many times begins to deform. At some point, the material cracks and begins to let mud and water in. Less expensive kits rarely provide the heat resistant material to account for this. Our goal is to avoid these areas. This can take more time and more material, but goes a long way to extending the life of the snorkel and the UTV.
What does a Snorkel do? A snorkel kit is intended to provide clean, dry air to the engine and other parts needing venting on UTVs such as clutches, differentials, transmission, carburetors, and fuel tanks. This doesn’t necessarily mean the UTV should exceed the OE manufacturer’s stated maximum rated water line depth. The snorkel kit is intended as additional margin of protection in the event that the UTV is inadvertently driven into water deeper than the OE manufacturer’s air intakes will tolerate. There are many considerations to make when increasing water line depth and a snorkel is just one component.
We know a little about taking off-road vehicles to the extreme - especially when it comes to deep water and mud. Trust us to protect your ride from deep water hazards with Diver Down Snorkels by High Lifter Products.
UTV Direct Return Policy
Eligible items may be returned within 30 days of receiving your order. All returns must be submitted through the UTV Returns Center and are subject to inspection before a refund or exchange is processed.
- Items must be returned within 30 days of receiving them.
- Items must be returned in new, undamaged, uninstalled condition and in the original packaging.
- Windshields with the protective covering removed are not returnable.
- Special-order and custom items are non-returnable.
- Return shipping expenses are the responsibility of the customer unless UTV Direct shipped the incorrect item in error.
- Exchanges will not be shipped until the return has been received and inspected.
- The original shipping cost may be deducted from any returned order that received free or shared shipping when the order was placed.
- Returned items that do not meet return requirements may be denied a refund or exchange.
High Lifter - 20%
During checkout, we ask for your year, make, and model. UTV Direct is not required to verify fitment on the products selected. It is ultimately the customer’s responsibility to confirm that the products ordered are correct for their vehicle. Fitment information is listed on each product page. If you are unsure, please contact our sales team before placing your order.
Refund timing may vary. You should generally expect to receive your refund within four weeks of giving your package to the return shipper, although many refunds are completed more quickly. This time period includes return transit time, inspection/processing time, and bank/payment processing time.
View Full Shipping & Returns Policy
Return authorization emails are typically sent within 2 business days. Please check all email folders, including spam and promotions folders.
